Home > Brake Light > 1996 Gmc Sonoma Brake Lights Not Working

1996 Gmc Sonoma Brake Lights Not Working


Cancel joestenny Rep: 19 2 Posted: 11/12/2015 Options Permalink History White wire off the brake switch and also with the cluster of wires front front to back is the brake wire The bulbs are fine and the fuses look good. turn signals, hazard and running lights work. Check your earth ... Source

viggy5802-11-2011, 12:19 PMno voltage on the white wire at the multifunction switch.. what a mess.. Ghetto Wagon 117,804 views 9:15 How to change an oil sending unit on 2007-2014 Chevrolet, GMC, Silverado, Suburban, Escalade. But not when it's clipped in on the brake. https://www.ifixit.com/Answers/View/32226/Why+dont+my+brake+lights+work

Chevy Truck Brake Lights Not Working

And thanks for all the help! Please try again later. On my 97 Jimmy neither the third brake light or the regular brake lights work. Cancel The All-New Pro Tech Toolkit The high performance electronics repair kit.

im lost any suggestions would be apprceated August 24 by gary price Have a 1998 GMC 1 ton the brake lights come on when I open the door and in the brake light dont work, all other's work except brake lites when I press the brakes, why? 04/28/2015 by prettyboyii196 1997 C1500 SUBURBAN LS 5.7 350 2WD brake lights worked until Tuesday To figure it out get a test light clean a piece of metal connect teat light ground, then unplug taillight and stick trat light probe into 1 slot at a time Brake Light Wiring Diagram Chevy Could it be a bad relay bay?

Hope that fix ur problem. 1994 Chevy Silverado Brake Lights Not Working When you make your connections, use rosin core solder and heat shrink tubing, do not use crimp connectors. Sign in Share More Report Need to report the video?

If you mean one in the middle, above the window or in the window, then no I don't have one.

Interested in Trek gaming? Gmc Brake Light Switch Replacement Rear Brake Lights/Turn Signal Lights Problem This is a discussion on Rear Brake Lights/Turn Signal Lights Problem within the Automotive Support forums, part of the Tech Support Forum category. It is a hard one to figure out but I also did check my trailer connection and it doesn't seem to be sending any power out to the trailer lights from thanks for the advice.

1994 Chevy Silverado Brake Lights Not Working

viggy5802-11-2011, 04:28 AMso, i'm gonna dive back into this tomorrow... old_master04-15-2011, 02:32 PMGood job, glad you got her fixed and thanks for posting back! Chevy Truck Brake Lights Not Working I just stuck the tester inside the fuse for the lights and got nothing. 1995 Chevy 1500 Brake Light Switch Question about 1999 Sonoma 1 Answer My left blinker and brake lights do not work when ...brake lights do not work when I have my headlights on.

So the frame was working as a power source....but only when the headlight/ running light circuit was on. this contact form Mark helpful 10 Report Ron answered 10 months ago I found the wires going to the tail light hang 1/2 inch below the bumper. no stripes on any of them. Look at the wires, because if it is not switch and not a bulb-fault, then as TBAS says it is probably wires, pinched or broken, from tail to switch to fusebox. How To Change A Brake Light Switch On A 1998 Chevy Truck

Sign in to add this video to a playlist. My fuses,bulbs,and break switch is good. Was this answer helpful? have a peek here Confession might be good for the soul, but it hurts the heart like hell. 07-08-2010, 06:51 PM #17 pspeir Registered Member Join Date: Jul 2010 Posts: 29 OS:

Ask a Question Usually answered in minutes! Chevy Brake Light Switch Wiring Went back to that ground again -- took it loose -- stripped the wire casing back a couple inches and BINGO!!!!!!!! Brake lights were working intermittently.

didn't fix it.

on the multifunction switch, i have 2 white wires. thoughts? it will most likely be beside your brake fluid assembly, in a cluster, entering the firewall. Brake Light Wiring Diagram 1994 Gmc Sierra All other lights work.

I'll add the steps for final removal to of the multifunction switch to the cleaning thread, unless you would prefer i start a new one. March 18 by Ryan Had the same problem..turned out to be a loose ground wire (broken terminal) on the front, lower, RH side of the engine. Proud supporter of the Carolinas Aviation Museum - the final home of Flight 1549. http://camtronics.net/brake-light/1996-acura-integra-brake-lights-not-working.html Sign in 193 57 Don't like this video?

DoctorD907 248,019 views 7:32 Brake light switch clip chevy truck 1988-1998 - Duration: 3:09. Check out the Dynaverse! Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. Interested in Trek gaming?

I also put this in the multi-switch "how to" thread Here's the final steps to completely removing the multi-function switch, should it need to be replaced: 1. Any idea Was this answer helpful? Rating is available when the video has been rented. Question about 1992 Sonoma 1 Answer 92 gmc sonoma...when i turn ...brake lights and reverse lights will not work when i turn the headlights off they will work..the taillights are flickering

Mark helpful 20 Report william257cash answered 9 months ago I had the same exact problem trust me i bought all new boards lights i even followed the line what you wanna Ghetto Wagon 274,529 views 3:09 1995-1998 Chevrolet GMC Brake Light Switch & Clip Removal Replace - Duration: 5:01. The wire was rotten ------------ Stripped the wire casing back real good and got to good clean un-rotten wire -- took a FILE to the frame rail rust 'till I found Is the switch adjustable?

Yes No Voted Undo Score 5 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Interested in Trek gaming?