it could be a number of things... Working... The Chevy dealer I took mine to had to have the cluster reprogrammed with the correct mileage. to $600. Check This Out
it could be a lose connection somewhere or you might need to spray some contact cleaner on the harness... The only reason I didn't fix it myself was that the car was under a used car warranty and how that this car didn't have that problem. naturalgurl98 Labadieville, LA #3 Apr 16, 2007 what is the cause? i couldn't tell you what it's called..
Judged: 2 1 Reply » Report Abuse Judge it! People are saying don't buy Chevy because of it. URL Please type the entire URL including the 'http://...' Title Description Your Email Address Preview your link: Not what you are looking for?
Judged: 5 Reply » Report Abuse Judge it! i grew up on Chevy's, but they have been nothing but a let down to me. took it in to get a tire fixed, turned out it's the wheel bearing AND need to change transmission. 2002 Chevy Impala Speedometer Not Working Do NOT buy the cheap BLACK Chinese ones, they are just as bad if not worse than the ... 13 Step 13: one of the four solder points that each stepper
Hello again, unfortunatley you cannot purchase an old one and install it or the odometer and saved settings will be wrong. 2006 Chevy Impala Speedometer Problems Any suggestions from anyone. - jealsop60, St. i use my tom tom gps for my speed. Please try again later.
Remove the screws from the I/P cluster trim plate. Chevy Malibu Speedometer Problems Remove the instrument cluster screws. Close Yeah, keep it Undo Close This video is unavailable. denco10-21-2009, 12:02 AMI had the same problem on my 2004 impala ss.I ordered the new servos off ebay and soldered them in it is not very hard.
I took it to a mechanic for the cluster and was told the valve body in transmission was bad so had it replaced. my company This MOST definitely needs to be a recall item to GM! - rbrow121nc, Charlotte, NC, USA Send Comment Add Complaint Read the next 20 complaints » About CarComplaints.com CarComplaints.com is an 2008 Impala Speedometer Problems http://www.autozone.com/az/cds/en_us/090... 2005 Chevy Impala Speedometer Stepper Motor Any and all info is appreciated.
Turned out to be not very difficult. his comment is here Well, this plastic breaks and because of the break it bends and jams the gear which then can't rotate to the proper pulses from the computer. I'll set them as close to the correct position as I can.
I just bought a 2002 sunfire. Now they want hundreds more to fix this WHY? - Clarence H., Tyler, TX, USA Send Comment Add Complaint problem #173 Jun 012010 Impala Automatic transmission80,000 miles Mine is just as 2007 Chevy Impala Speedometer Not Working
Add to Want to watch this again later? If under warrenty, take it to the dealer and should be covered for the replacement part. Reply View Public Profile Send a private message to dodavis Find all posts by dodavis CF Beginner Join Date: Nov 2007 Posts: 8 November 22nd, 2009, 12:16 PM #6 this contact form Over the past few months after this would happen the speed odmeter would be way off.
Sign in Share More Report Need to report the video? 2004 Chevy Impala Speed Sensor Location If that doesn't work, start looking for cracks in the other ones.
your best bet would be EBay to try to get just the shift indicator unit. If a new instrument cluster was installed, refer to the IPC Setup in the scan tool Special Functions menu.
HeMi10108-03-2009, 07:19 PMYes you can drive the car without it. I have a 2005 chevy impala.. Started to repeat 50-60 miles later. 2005 Chevy Impala Instrument Cluster The motor was used throughout General Motor's entire production line from 2003 to 2007.
The complaints are organized into groups with data published by vehicle, vehicle component, and specific problem. Sign in 56 20 Don't like this video? I did not calibrate mine I just put all of the pointers on zero then installed them at zero or empty etc.My gps says I am dead on with the speedo.the navigate here or Facebook Google Plus Forums Chevrolet Forum CommunityNew Member Welcome AreaForum NoticeRide of the MonthROTM Procedure & RegulationsROTM 2009ROTM 2008The LoungeNews, Concepts, SEMANewsletter ArchiveGeneral Discussion ForumsShow Off CentralGeneral TechREAD BEFORE POSTING
This ... 15 Step 15: After you De-solder the connections make sure that none of the solder is stuck on the board 16 Step 16: After removing the solder from all