Home > Ford Ranger > 2000 Ford Explorer 4wd Not Working

2000 Ford Explorer 4wd Not Working


Perform GEM self-test. If voltage is present, repair short to voltage in White wire. Clear DTCs and retest system. 46. All tips on this site are for use at your own risk and discretion. have a peek here

See Fig. 3. Dave Westminster, MD #8 Feb 17, 2014 98ranger4xlt wrote: no that sounds more like the vacuum hub you will have to switch the hub to manual lockout hubs instead of vacuum No, create an account now. It turned out to be the Control Module under the kickplate.

2002 Ford Ranger 4x4 Control Module

FOLLOW THE LINK (copy and paste if you have to)http://www.therangerstation.com/forums/../Magazine/Apr04/offroad.htmLet me know what you think! 0 · Share on Facebook grumpy77 Posts: 3 April 2009 what if 4wd hi works but You mentioned replacing the module, which module are you referring to? Look HERE for information on replacing it.

Held by 2 bolts and has a plug. He said that his 97 problem was a switch on the firewall directly behind the motor and costed $400 to fix it. If voltage is not more than 10 volts, check power distribution box fuse No. 3 (20-amp). Ford Ranger 4 Wheel Drive System now i got a used 4wd module prob.

Connect jumper wire across terminals No. 2(Brown/White wire) and No. 6 (Yellow/White wire) on transfer case 8-pin harness connector. Ford Ranger 4 Wheel Drive Problems I accessed the switch was bad & replaced it. Using DVOM, measure voltage on Light Blue/Black wire between ground and terminal No. 10 at GEM 22-pin harness connector. http://www.explorerforum.com/forums/index.php?threads/4x4-does-not-work.163694/ Dealer wanted 380 for the moduler at that time.

If resistance is not less than 5 ohms, repair open in Light Green/Orange wire. 1999 Ford Ranger Four Wheel Drive Problems The motor will need to be replaced. If voltage is more than 10 volts, repair open in Tan/Yellow wire. Clear DTCs and retest system.

Ford Ranger 4 Wheel Drive Problems

We tried that and the lights turned off for a while but came back on. great post to read Check Fuse No. 26 Inspect fuse No. 26 in fuse junction panel. 2002 Ford Ranger 4x4 Control Module Be polite. Ford Ranger 4 Wheel Drive Wont Engage If voltage is not present, replace GEM.

Using DVOM, measure voltage on Tan/Yellow wire between ground and terminals No. 1 and 5 on battery saver relay socket. http://camtronics.net/ford-ranger/2000-ford-ranger-heater-not-working.html Check Battery Saver Relay Coil Circuit Trigger GEM active command BATT_SAVR to OFF. If resistance is not more than 10 k/ohms, repair short to ground in Violet/Orange wire. Enter Username Enter Numbers Please note by submitting this form you acknowledge that you have read the Terms of Service and the comment you are posting is in compliance with such 2001 Ford Ranger 4x4 Fuse Location

Measure Circuit 792 Voltage Turn ignition off. This was not the problem. It all works now - for how long, who knows...QUOTE] Hi jobewan. http://camtronics.net/ford-ranger/1996-ford-explorer-odometer-not-working.html Any ideas?

Is it definitely not going into 4WD Hi or Low? 1999 Ford Ranger 4x4 Manual Locking Hubs None of the LED's (Auto, High, or Low) on the switch light up. Not ?


Clear DTCs and retest system. See Fig. 6. U-joints appear to be in good condition and the bearings are good. 1999 Ford Ranger 4x4 Vacuum Diagram Solution #2: If you have an extended cab, this can also be caused by a bad carrier bearing.

Check for bad connectors or broken/damaged wires/harness. Disconnect shift control module connector. See Fig. 3 and Fig. 6. this contact form Thanks, Jobewan jobewan, August 31, 2006 #9 Kbonz66 New Member Joined: September 3, 2006 Messages: 5 Likes Received: 0 Trophy Points: 0 City, State: Alabama Year and Model: 1993 Ranger

This feature is not available right now. This happens approximately every 10 seconds or so. So now the transfer case is the disease. Anyone know an internet link to buy a control module?