Home > Ford Windstar > 1999 Ford Windstar Brake Lights Not Working

1999 Ford Windstar Brake Lights Not Working


During vehicle operation, ABCM monitors all electrical ABS functions and some hydraulic operations. Was this answer helpful?YesNo Tuesday, November 18th, 2008 AT 8:49 PM 8lugnuts Member The scanner returned a code indicating that the REM needs to be replaced. While I had the module exposed and still plugged in I started pulling the plugs(there are five), when I pulled one of them the rear tail parking light which is working If that doesn't fix it, there's a remote chance you have pinched or damaged wiring at the tailgate. Source

I know you have to deal with hundreds of one a be's like me every day. What electric car is the best? ABS/TC Module OPERATION When brakes are applied, fluid under pressure is transmitted through 4 normally open solenoid valves located inside Hydraulic Control Unit (HCU) to wheels. Not common to me on this vehicle but other Fords have had short wires to the switch which would pull on wires in the plug in rendering it useless. navigate here

1999 Ford Windstar Rear Electronic Module

I've opened up all the wire bundles in the rear door/ taillights / rear headliner areas and have found nothing amiss. I don't think it is anything to do with a control module. The data lines from this module only go to the turn signals at the rear? Peter Rhyne 45,941 views 6:11 Brake lights stay on?

SPONSORED LINKS Was this answer helpful?YesNo Wednesday, November 20th, 2013 AT 7:33 AM saturntech9 Expert 30,130 posts I have a crappy wire diagram it shows the red wire with a yellow The bulb works on both tail light and brake light when moved to the right side. On the right hand top of the rear door, I found the primary ground wire partially broken. 1999 Ford Windstar Tail Light Problems Your windstar is a late model and the other one is an early model so it doesn't have one.

Loading... How about '99? DESCRIPTION & OPERATION Vehicle has 2 module communications networks. please help whats the problem? 2000 Ford Windstar 3.8L links removed (This post was edited by Hammer Time on Feb 21, 2010, 5:07 AM) TomGreenleaf Ultimate Carjunky / Moderator Feb21,2010,9:43AM Post

Print Thread Email This Post Auto Repair Home>> Automotive Repair>> Car Troubleshooting rshaw45005 New User Feb20,2010,8:30PM Post #1 of 3 (7263 views) Brake lights not Working on 2000 Ford Windstar 2001 Ford Windstar Brake Lights Not Working You can only upload videos smaller than 600MB. Credentials confirmed by a Fortune 500 verification firm. Loading...

1999 Ford Windstar Brake Light Fuse

She's afraid to have that last beer when she's out with her friends for fear of getting puled over. :) SPONSORED LINKS Do you have the same problem?YesNo Wednesday, November 20th, NativeSD53 1,385 views 1:21 Fix to Brake Lights not working and blow fuse on 2003 Ford Focus - Duration: 2:37. 1999 Ford Windstar Rear Electronic Module Dan. 1999 Ford Windstar Rem Location GEM generic electronic module.

I'll bet if I took it to a Ford dealer they would figure it out pretty fast but I'm not ready for that yet.$$$ Was this answer helpful?YesNo Friday, November 21st, this contact form I've checked all the connections and found all to be clean and tight. Mark Goldberg 256,721 views 26:26 Brake Light Switch Replacement - Duration: 7:47. I first tried to clean it but the same problem arose which was car dying while driving with no other ... 1999 Ford Windstar Cargo - Maintenance & Repair I have Rear Electronic Module 2002 Ford Windstar

I think I didn't suspect the sockets because the both went out at the same time and I assumed it was the REM since so many people were having issue with But most likely the bulbs are just the problem. Power to the lamp is good. have a peek here Sign in Transcript Statistics 1,456 views 3 Like this video?

Upvote (1)Flag inappropriateCOMMENT by fdny, December 15, 2010Thanks!!! So if ya looking to buy one, those are the models you need to look for. Looking for vehicle trackers?


Dan D 12Ounce01-26-2005, 05:00 AMIf you are talking about the Right Rear Stop/Park lamp, it goes like following: . The reverse lights work and the signal lights do work.When you put the lights for night driving, they lights work in the back too, but the do do get brighter indicated Latest Forum Post Transmission advice for my '89 Buick Century Hi, I'm looking for advice on repairs fo... The air bag diagnostic monitor and all other optional modules, the Generic Electronic Module (GEM) and Anti-Lock Brake System (ABS) control module (on models not equipped with traction control), are connected

I have checked the wiring diagram for the ABS/TC module and cannot find any output wires to the rear lights? Oh, and I have no tow package on this car.... intermittent clicking noise under dash 11/8/2016 11/8/2016 fordguy4u I have no brake lights on my cvpi, they worked 11/8/2016 11/8/2016 fordguy4u Have brake, turn signals,no taillights. Check This Out Same van, same year, same model (LX vs Northwood LX) why the heck does Ford do this!

Apparently there are several different versions of this module depending on how your van was optioned. If you ground the light it will never turn off. First tell us what Make you're interested in. Replaceing it will likely correct this issue on your 1999 Windstar.

Seriously, change the bulbs. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! Cant find fuse location in Owner's manual for brake lights??? Behind dash left side of steering column.

Loading... can you pls tell me how to get to this so I can see it has come loose, Th... 2003 Ford Windstar Cargo Base - Maintenance & Repair Dashlights went out Also are the wire colors correct the way I said they were? SPONSORED LINKS Was this answer helpful?YesNo+1 Tuesday, November 18th, 2008 AT 6:41 PM Dave H Expert 13,547 posts **stop press**there is another module?

Justin Peters 11,498 views 2:37 #1 Reason Your Ford Cruise Control Doesn't Work Anymore - Duration: 3:48. Also, I noticed a post on another site that referenced the Light Control Module (LCM) - could this be a cause as well? The brake lights are not working. I have tested the connection at the plug and both plugs are getting 12 volts when the lights are on with one wire each and two when the brakes are applied

wire color is gray/red.