Home > Fuel Gauge > 1986 Chrysler Fuel Gauge Not Working

1986 Chrysler Fuel Gauge Not Working

Contents

Mark The administrator has disabled public write access. #11178 classicfins Contributing Member Posts: 778 Re:Gas gauge problem.. Category:Dodge Share this conversation Expert: George H. You can clean the connections, but be careful that the foil doesn't peel loose from the flexible plastic "board." The board is fairly durable, but doesn't like to be bent excessively.Hope General Motors Fuel Gauge TroubleshootingFuel gauge troubleshooting begins with isolating the problem either to the gauge, sending unit, fuse or wiring. http://camtronics.net/fuel-gauge/89-yj-fuel-gauge-not-working.html

Logged 1979 K10 2004.5 Dodge Ram 2500 4x4 2006 Chrysler 300C SRT8 1975 Harley Davidson Ironhead Captkaos OWNER and Administrator Administrator Senior Member Posts: 17614 Re: Fuel Gauge I would rather spend $30 instead of $80, but if I need the tube type to be accurate I will go that route. The jumper wires (or test box) can be used either at the gauge or sending unit. My main concern is the bottom of this mount is tapered upwards as it goes forward, and the gas tank does too best I can tell.

Fuel Gauge Problems Chevy Truck

If the gauge doesn't respond appropriately when the resistance in the sending unit circuit is changed, check the hot terminal at the gauge to see if it's receiving voltage. Thanks guys. If it’s not, I would suggest you start there.

RAM MAN is offline Quick Reply RAM MAN View Public Profile Visit RAM MAN's homepage! If I dimmed the dash lights all the way to off the gauge worked. For example a 69 Camaro has a 0-90 ohm fuel sender. 1979 Chevy Truck Fuel Gauge Not Working Does the temp gauge work too?

On non-molested cars, there is usually a clip that jumps across the rubber hose from the sending unit nipple to the fuel line. 1978 Chevy Truck Fuel Gauge Problems The front of the rheostat shows which side the float should stick out from. Using a small hose clamp, clamp the wire to the nipple. Connect your test light to a hot position on the fuse block and test it to ground to make sure it lights up.

Schrodingers Box 391,134 views 16:23 Fuel Gauge Troubleshooting - Duration: 6:43. 1985 Chevy Truck Fuel Gauge The tank I have is a triangular one that fits inside the triangular motor mount on the rear of the pontoon boat. I strongly advise you disconnect the battery while removing the cluster. The following process will require the ignition switch be in the “on” position for troubleshooting a fuel gauge issue.

1978 Chevy Truck Fuel Gauge Problems

If you have a 240-33 or 73-10 Ohm sender then the sender may not have a proper ground or there is a break in the sender lead wire. I used the prong that is supposed to be the ground to check the ignition hot. Fuel Gauge Problems Chevy Truck Follow the circuit trace to the fuel gauge, one leg goes to the pin of the gauge and the other pin of the gauge goes to pin "C" of the panel C10 Fuel Gauge Not Working Remove the driver sidekick panel and locate the multi-connector going to the rear of the car.

Expert: George H. this contact form The main problem with a float type will be if the arm will have free travel or will it contact the inner surface. This is not as complicated as it sounds. Credentials confirmed by a Fortune 500 verification firm. Chevy Fuel Gauge Reads Past Full

Mark helpful 15,545 Report chassy answered 2 years ago If you can't fix it easily, remember - it's only a convenience, it's not an essential. 1 out of 1 people think Note the color of the wire at the tank. My gas gauge would work except when I pulled on the lights. http://camtronics.net/fuel-gauge/206-fuel-gauge-not-working.html Take your test light and connect the one end to ground.

I could see anything wrong with it but I bought a used one from the pick and pull and that was it. 1984 Chevy Truck Fuel Gauge Not Working Ideas? But before we dig into this, check the fuse for the instruments.

The gauge should go full scale, then open the sender wire and the gauge should go full scale in the other direction.

Just the fuel gauge is out Supplement IF the dash cluster has a printed circuit board, double check to be sure it’s in tact and there are no burned traces. A range of 33 to 240 ohms comes to mind. Set your Multi-meter to 0-100 Ohms. 73-87 Chevy Truck Fuel Gauge Wiring Smear some Vasoline on the connections and reconnect the plug.

Ask Your Own Dodge Question Customer: replied7 years ago. Scotty Kilmer 389,841 views 2:59 Loading more suggestions... Determine which wire is the sending unit wire. Check This Out Ground the sending unit to the body.

Electronic displays usually have their own self-contained voltage regulator in the fuel gauge control module. If that post is grounding out you will only see zero ohms on a gauge or multimeter. Not much good for anything, but they sure are fun to push down the stairs. Thanks George.

Defective Dash Voltage regulator (Voltage limiter) or gauge 2. Those two numbers will tell you the ohm range is of your sender. Check the voltage output of the regulator with a volt meter. If you have any lights on the dash, oil light (Idiot Light) turn signal indicator and they work, then a ground is established.

To get at the voltage regulator, you have to remove the instrument panel. You should generally find somewhere between 10 to 15 ohms resistance. Page: 1FiberGlassics® ForumsHomeMain Forum Moderators: kensikora, , classicfins, bruce gerard, billr, mrusson, cc1000, MarkS, Waterwings, jbcurt00 Board Categories Home... This is my first post and I'm hoping I can get some answers.

But which one is it? After that the speedometer wworks but the odometer doesn't??/ When i pushed the reset, it might have felt a l... 1988 Chrysler Le Baron Base - Maintenance & Repair electronic instrument Make sure the wires are connected to the posts. Or possibly the center terminal on the sending unit itself is grounding out against the body of the car.

To check the gauge, you can simulate input from the sending unit. I assume you haven’t put the cluster back in by now. Expert: George H. Some people are like slinkies...

The amount of current flowing through the gauge heats up the bimetal strip. Enter Keywords or a Phrase: Be sure to visit our other websites: Auto Repair Yourself CarleySoftware OBD2HELP.com Random-Misfire.com Scan Tool Help TROUBLE-CODES.com Skip navigation UploadSign inSearch Loading...