Home > Instrument Cluster > 2003 Gmc Sierra 1500 Speedometer Not Working

2003 Gmc Sierra 1500 Speedometer Not Working

Contents

For Silverado, Tahoe, Yukon, Suburban, Sierra, H2, Avalanche and other 2003, 2004, 2005 and 2006 Chevrolet GM vehicles. When traveling long distance and stopping for gas upon restart the speedometer will not work properly. the issue is cold solder joints on the front of the circuit board. This means that you cannot reply to this topic. 24 replies to this topic #1 04SilveradoLT 04SilveradoLT Enthusiast Member 324 posts Posted 13 December 2008 - 07:04 PM My speedometer stopped Check This Out

This lasts for awhile then it goes crazy again.(at closer intervals each time) Today my RPM indtrument went crazy as well.(read as low as possible)What's happening. And work its way up to beyond 120 mph at moderate speeds. My vehicle DOES NOT qualify for the settlement. Stepper Motor Back to top Page 1 of 2 1 2 Next Back to 1999-2006 & 2007-2013 Chevrolet Silverado & GMC Sierra 1500 · Next Unread Topic → Reply to quoted

2005 Chevy Silverado Speedometer Not Working

Sign in to add this to Watch Later Add to Loading playlists... briansmobile1 126,796 views 23:46 How To Replace GM Stepper Motor & LED Lights In Dash - Duration: 7:03. The speedo started working as soon as I started back up.

The result was successful, the tranny and speedometer work correctly now! 33 out of 33 people think this is helpful. A second person for this is the ticket, if your solo like I was for one of the installs it is tricky but after resting case on chest it worked out. Register now! 2003 Gmc Yukon Instrument Cluster Problems what did you end up doing?

Does anyone have an idea of what themayis be? 2003 Gmc Sierra Instrument Cluster Not Working pulled it, started the engine, shut off the engine, replaced the fuse. I found you! http://www.topix.com/forum/autos/chevrolet-tahoe/T7IEVBBFPJQIQHNVG/p2 I know, I know call the dealer and ask.

Josh K 20,562 views 3:09 Dash lights - how to replace GM dash lights gauges Chevrolet, Buick, Cadillac, Pontiac - Duration: 5:34. 2004 Gmc Sierra Instrument Cluster Dead I cleaned the MAS, replaced shift sensor, made sure trans fluid was full, disconnected and reconnected the battery, and now I am thinking of replacing the stepper motors for the speedo I like the design for install lol. At about 70,000 mi.

2003 Gmc Sierra Instrument Cluster Not Working

When I would turn it back on it would start from that point. http://www.instructables.com/id/DIY-Finally-How-To-Repair-a-GM-Instrument-Cluster-/ I'd be willing to bet that anyone who encounters this problem will find the solution only through tracing ground connections within the harness..... 2005 Chevy Silverado Speedometer Not Working My water pump went and from that point it hasn't acted up. 2004 Chevy Silverado Instrument Cluster Not Working It is mounted on the tailshaft of the transmission and is held it with one small 8 mm bolt.

Loading... his comment is here Tampatec 7,870,660 views 4:02 Vehicle Speed Sensor Removal & Installation - Duration: 8:47. Once that happens, I have to manually shift it out again. For Silverado, Tahoe, Yukon, Suburban, Sierra, H2, Avalanche and other 2003, 2004, 2005 and 2006 Chevrolet GM vehicles.In this tutorial you'll learn how to repair a sticky, stuck, jumpy or dead 2003 Gmc Yukon Instrument Cluster Recall

Mark helpful 190 Report Mark answered about a year ago I have no power to the 10 amp Trans fuse. Thanks for sharing you knowledge, especially knowledge that can help save money!

More CommentsAbout This Instructable 322,291views61favoritesLicense: None (All Rights Reserved) DrSpeedometerDr.SpeedometerFollow11More by DrSpeedometer:Add instructable to: Contest GroupRelatedErratic Instrument Panel on Upvote (7)Flag inappropriate2004 GMC Sierra 1500 138,000 mi, VisitorTemp. this contact form Doc Speedometer 46,261 views 5:42 2004 silverado...

Same deal. 2004 Chevy Silverado Speedometer Cluster CarGurus has 56,871 nationwide Sierra 1500 listings starting at $2,695. Sign in Don't like this video?

Mark helpful 75 Report juggaloscorpio answered 2 years ago check the ignition switch harness for power drops across the white wire and the pink wire...

The cluster has been replaced, the speed sensor has been replaced and even some wiring has been replace. Close Yeah, keep it Undo Close This video is unavailable. Yes No Voted Undo Score 0 Cancel Comments: what engine and what type of tranny do you have? 10/19/2011 by oldturkey03 Add a comment 0/1024 Cancel Post comment Are you sure 2004 Chevy Tahoe Instrument Cluster Fuse I am very far from being a mechanic.

Sign in to report inappropriate content. the issue is cold solder joints on the front of the circuit board. Our technicians tell us that the instrument cluster must be sent to a repair facility to correct this fault. http://camtronics.net/instrument-cluster/2003-gmc-sierra-instrument-panel-not-working.html Codes thrown in one instance where it says that the speed sensor or one of the temp sensors, or the IAC, or the map sensor is the cause, will only pop

Not ? Thanks for your comment! AND I.D. . Upvote Flag inappropriate«12»Related Items:Check Engine Light With Code P1870Vehicles equipped whit a 4 speed automatic transmission may develop a harsh 1-2 shift and/or il...Verified for the GMC Sierra 150013 reportsNew Fob/Entry

Username Forum Password I've forgotten my password Remember me This is not recommended for shared computers Sign in anonymously Don't add me to the active users list Privacy Policy Which did not fix them! Only a couple of days ago so not tested good. Upvote (2)Flag inappropriate2016 GMC Sierra 1500 120 mi, VisitorThe speedometer would pulse about 5 or 6 times on a row when I opened any of the doors.

Start truck. Tools needed 11 mm box end for u joint saddles 15 mm small 3" box end, 1/4" ratchet with 15mm socket 18 for drain plug, 19 for sensors Oil transfer hand MrSubaru1387 100,963 views 11:33 How to Fix a GM Speedometer & Instrument Lighting - Duration: 23:46. In replacing the cluster will it reset the odometer or will the computer maintain the mileage after you unplug the old and add the new one?

The small 1/4 ratchet is a dream for 5 top and side nuts, box end for bottom nut but leave bottom nut tight until wiring is unplugged because trapped oil in Cancel Ryan Rep: 25 1 Posted: 03/07/2012 Options Permalink History I know it's an old thread. If you can't find the problem we could take a look at it for you, I'm sure we could get it. Sign in to make your opinion count.

DIY BRI shows you how.Here is a great priced link to buy a kit for 6 gauges, plus it comes with a few bulbs http://amzn.to/2eTELM5Here is a link to buy the