I would definitely check the resistor first. Thanks for the Info, It was very helpful and turned what would have been an hour job for me into ten minutes. The new resistor was good but I found out that the wires in the harness that connects the resistor to the blower were backwards, causing the blower to still run but Is there any other information you can provide us with? have a peek here
Thanks Cam, I'll give that a shot. rekjavicxxx 15,774 viewsNew 4:17 Blower Motor Problems | Auto Repair Help - Duration: 4:22. I was referring to the weather just to make a point that it is really hot and I'm not happy with subpar A/C. INSTRUMENT PANEL SIDE BOLTS: Some models use the large bolts at each end of the instrument / dash panel to provide ground path to the chassis.
i just did all that and again it didnt start at all what do u think it is August 5, 2011 at 1:02 PM Chris said... March 26, 2012 at 4:09 AM Anonymous said... Can't be harder than changing a light fixture or outlet in a house. I have had a new thermostat fitted and the 2 heater doors ... 1999 Jeep Grand Cherokee Limited - Maintenance & Repair The fan relay keeps going bad any ideas of
Unfortunately, one of the wires melted the harness to the old resistor making it a bit difficult to remove. This feature is not available right now. I paid 140.00 for my resistor for 2001 Grand Cherokee. 2000 Jeep Cherokee Blower Motor Resistor Jim.
I replace the blower motor resistor ($30) and tried to start it but no go. 2004 Jeep Grand Cherokee Blower Motor Resistor I removed the glove box and trim. Take a look at the fuse box and see what they look like. http://www.topix.com/forum/autos/jeep-grand-cherokee/TAI581A5BM7MK7K3G Some viewers have commented that their wire harness was melted.
Do you think that replacing this resistor will fix this issue? 1997 Jeep Grand Cherokee Blower Motor Resistor Location I double-checked the relay fuses or plugs under the hood and found the problem. There is a gray plastic retainer that is then installed around the three wires that were just inserted into the connector. I would recommend that you find by searching the internet.-Bobby August 1, 2011 at 10:20 AM Anonymous said...
you can get an universal relay at advance auto parts for 65 and it will work fine. http://www.wjjeeps.com/blower_motor.htm It's a large black box, which I'm assuming holds the actual resistor. 2002 Jeep Grand Cherokee Blower Motor Replacement I went to the dealership and they wanted to charge me 205 dollars for this 15 minute job. 1999 Jeep Grand Cherokee Blower Motor Replacement Are they missing?
June 13, 2011 at 7:46 PM Anonymous said... navigate here Had to replace the wiring harness also since one terminal was burnt out. Reply » Report Abuse Judge it! Password Register Forgot Password? 2001 Jeep Grand Cherokee Blower Motor Relay
Not fixed yet. I have one problem....I have a 1999 Jeep Grand Cherokee and recently replaced the blowere resistor due to losing all speeds on the blower. Blower motor switch - description The A/C Heater blower motor is controlled by a rotary-type blower motor switch, mounted in the A/C Heater control panel. http://camtronics.net/jeep-grand/1999-jeep-grand-cherokee-heater-fan-not-working.html Thanks for posting this...a great help.
Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... 2001 Jeep Grand Cherokee Blower Motor Fuse October 28, 2009 at 4:37 PM bvensko said... @ Kube82, I would definitely replace the wire harness. You can see burnt connection by removing cover.The module wires connect directly to blower motor(backward trace to find) Reply » Report Abuse Judge it!
I'm still not satisfied with this, should I go to junkyard? On vehicles with manual temperature control systems, the switch allows the selection of four blower motor speeds, but will only operate with the ignition switch in the On position and the ONLY FILL ON THE LOW PRESSURE. 2000 Jeep Grand Cherokee Blower Motor Replacement On manual temperature control systems, the blower motor switch is connected in series with the blower motor ground path through the a/c heater mode control switch.
Picked up the part for $30.95 at the dealer and replaced it in 5 minutes. October 13, 2009 at 8:24 AM Anonymous said... Instead we pay $$$ the big guy, who I'm sure really has no idea on how to really do the work, for instructions. this contact form March 5, 2012 at 7:14 AM Anonymous said...
If so we invite you to join our community and see what it has to offer. The A/C would blow on high (4) only. The connector or terminals should be replaced; a replacement connector is available. Not fixed, looking for a solution.