Home > Jeep Wrangler > 1997 Jeep Wrangler Gauges Not Working

1997 Jeep Wrangler Gauges Not Working


All youhave to do to fix the connection problem is this. Robert Nauert 25,758 views 1:08 Diesel Jeep Drives 12 Feet Underwater! - Dirt Every Day Ep. 54 - Duration: 25:52. STINSONShobbies 3,813 views 7:32 Jeep Check Engine and Cluster Diagnostic Tricks - Duration: 6:40. Hope This Helps. Source

I had the same problem with my 1997 Wrangler. Ask Chad Your Own Question Chad, Lead Master Tech Category: Jeep Satisfied Customers: 1112 Experience: Electrical master,Diesel Specialist,Lead Tech/shop foreman 12781541 Type Your Jeep Question Here... If everything works again, you have found your problem. Expert: Chad replied5 years ago.

Jeep Wrangler Instrument Cluster Failure

Wind That Clock Symptom: Horn stops working, cruise control stops working or works sporadically Affected Model(s): '95-'01 Cherokee, '97-'06 Wrangler Cause: The clockspring in these airbag-equipped Jeeps passes the power from Some other things to check are: Pull the blower motor switch apart and check for burned connectors Check amperage of blower motor (should be under 5 amps on high) Check resistor I have read a lot of stuff on the net about this issue and nothing has worked so far. 09-19-2013, 07:15 AM #30 AUSJEEPER Newb Join Date: Sep I removed the lower sections of my dash, do i have to remove more to find it?

hate to buy if not sure it is the problem. Here is the recall number: 99V117000 Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members Sign in to make your opinion count. Jeep Wrangler Instrument Cluster Not Working Share on Facebook Share on Twitter Share on Google+ Share on Pinterest Share by Email × Question about 1997 Jeep Wrangler 2 Answers 97 Jeep Wrangler Dash Gauges Arent Operating..everything else

tach will work for 5 seconds then quit, I have noticed that when I wiggle the ignition key to make the relays turn on the tach will work but only for check the wire near Diesel pump solnid, put a wire from +ve teminal of bettery check the solnid is working or not? You can only upload files of type 3GP, 3GPP, MP4, MOV, AVI, MPG, MPEG, or RM. http://www.wranglerforum.com/f210/1997-wrangler-instrument-panel-dead-1392.html After I figured out that the ground "needed" to be established fo the radio to work, I thought maybe this was true for the dead gauges.

The auto repair forum is collaborative member forum for you to find solutions to your car problems. 1997 Jeep Wrangler Fuse Box Diagram Quick Flashing Symptom: Blinkers and/or hazards flash quicker than a monkey on meth doing semaphore Affected Model(s): All Cause: Either you just swapped in LED lights somewhere, or you lost a Or just drag it here! Use new dielectric grease prior to reassembly.

Jeep Wrangler Gauges Dont Work

Pabst Boys Roadhouse 8,658 views 13:07 Jeep Wiring Diagrams / Schematics - Duration: 1:08. get redirected here Loading... Jeep Wrangler Instrument Cluster Failure Even when you turn the ignition on before you start the car, all dash indicators light up. 97 Jeep Wrangler Instrument Cluster Problems So I wiped it off with a paper towel and now everything works.

but I don't know how to use it to check voltage. http://camtronics.net/jeep-wrangler/2000-jeep-wrangler-gauges-not-working.html Because I don't believe the cluster going out wold make the radio go out.you could use a test light to check the pins I mentioned. The vehicle starts just fine and the lights all come on when the headlights are on. Either bend the tab so it is further away, use a bungee cord to hold the pedal up when not in use, or buy a new brake assembly. 1998 Jeep Wrangler Gauges Not Working

Check voltage where it goes into the firewall on the engine side and voltage at the fuse block. Ask Your Own Jeep Question Customer: replied5 years ago. Periodically the gauges on my 2000 Jeep Wrangler quit working and the airbag light pops on and off and then the odometer flashes up "No Bus". have a peek here check fuse #17 in fuse box under hood.

behind the cluster there are two female recievers... 1997 Jeep Cherokee Gauge Cluster Not Working In some instances the factory-supplied grease itself was the culprit. Remove them and the black cover.6.

Sign in to report inappropriate content.

Vender quotes NEW!! Come See Us At River Rock Orv Park. Indicater lights in cluster seem to be ok. 05016261aa Page 1 1997 Jeep Wrangler-- Gauges don't work.

Please upload a file larger than 100x100 pixels We are experiencing some problems, please try again. I understand the cluster, but is it a ground problem or what? 03-06-2011, 01:11 PM #23 NWPATJ Jeeper Join Date: Dec 2008 Location: Geneva, Pa Posts: 59 I would have to say the cluster and the radio are both bad. http://camtronics.net/jeep-wrangler/97-jeep-wrangler-gauges-not-working.html Is there another fuse for just the gauges?

Trending I want to rebuild my jeep Cherokee inline 6(: what things specifically should I replace? 4 answers Flickering interior lights? 6 answers Can i change my 2000 jeep grand cherokee What would be the best all terrain tire? 1997 Jeep Grand Cherokee door lock problems? Sounds like that could be the problem. I could have done it in 10 minutes, if I hadalready known how to take the dash apart.Here's how it works.

It seems to me the light should have been taken care of with the module replacement. Again, be sure to be careful about not breaking that wire. Either simply, a blocked fuel line (debris / filter / fouled gas) or an electronic issue.