Home > Speedometer Not > 1998 Volvo Speedometer Not Working

1998 Volvo Speedometer Not Working

Contents

Tasca still shows speedometers available new starting at $550 as of 7/2010. The ABS light did turn on and I did reflow the solder joints but the speedometer still would randomly quit on me so I just got another one and all is ABS seems to be under fuse box as described. If the board indicators are obscured, note the orientation of the existing capacitors BEFORE you remove them: the white stripes are on the negative sides. http://camtronics.net/speedometer-not/98-volvo-speedometer-not-working.html

E. Alternator/Voltage issues. No guaranties though but you lose nothing by trying it anyway. The second method is shown below as the Needle Method and is easier. http://www.matthewsvolvosite.com/forums/viewtopic.php?t=28142

1998 Volvo S70 Abs Module

You'll also typically get a pump motor code which is along the same lines, the pump itself rarely fails, but the pins inside the module that control it do. Ignition switch. With the board loose you have access to both screws that hold the odometer motor in place. Loading...

See Soldering Tips above. From what I've gathered so far it's either the ABS wheel sensor(s) or the ABS Module. Once most of the solder is removed the ribbon still will not separate freely as any residual solder would still hold the ribbon in place. Abs Light On And Speedometer Not Working The removal of the face will reveal two small Phillips head screws that when removed will leave the mechanical portion of the odometers free of attachments.

It works like a charm. Content copyright . If you are on a personal connection, like at home, you can run an anti-virus scan on your device to make sure it is not infected with malware. http://volvospeed.com/vs_forum/topic/108115-speedometer-not-working/ Release the needle so it goes back to 0 and rests on the stop pin.

Does a car clunk/jerk/hesitate when going into safe mode? Volvo Speedometer Repair The dash board disassembly is the same also for the VDO model. [Editor] Your speedometer or circuit board may vary from the diagrams shown for the 940; the parts needed may It's important to remember that there are other parts of the ABS system, and like anything else problems do come up. S40 / V40 '96-'04 General Forum for the Volvo S40 and V40 (Classic) Series from 1995-2004.

Volvo V70 No Speedo

Or sign in with one of these services Sign in with Facebook Sign Up All Content All Content This Topic This Forum Advanced Search Browse Forums Gallery Garage Downloads Blogs Calendar The speedo started working again however is erratic plus the ABS kicks in at low speed - I swapped the ABS ECU and still the same. 1998 Volvo S70 Abs Module Always double check your large harness when installing, make sure it is 100% bottomed out and locked into place. Volvo 240 Speedometer Not Working Some yards won't take them back either, because they're an electrical item.

If you have any problems with the registration process or your account login, please contact contact us. this contact form When you put it back on, set it so it full stops clockwise at over the k in km/hr bottom mark. Getting the capacitors off is done by twisting the cap side to side as you heat each leg pin from underneath to break the solder with the heat. You might also want to check if the wiring is not frayed or damage. 2000 Volvo S40 Speedometer Not Working

Up next ipd Volvo - Odometer Repair for 200 Series Volvo 1986-1993 - Duration: 9:05. The needle is then removed by very gently turning it and lifting straight up after you carefully lift it over the zero peg. GENTLY spin and wiggle the pick around until it breaks loose, then remove it from the hole. have a peek here Abs sensors will be my first port of call after establishing I have a bulb in my dash.

Mr Pies Original Poster 6,775 posts 98 months [report] [news]Friday 30th September 2011 Davie said: Does the brake warning lamp work, ie the red "!" On mine (1999 V70) the speedo 1998 Volvo S70 Speedometer Intermittent The solder needs to be removed without removing or damaging the tube or the foil around it. Desoldering Tips: [Paul Ramdial] As I am somewhat proficient with soldering and such I felt more comfortable working with the PCB off the unit.

over 50mph clears the codes.

Remove the iron and let the solder harden. You will see the needle stops about over the km on the km/hr stamp. Or just replace the lot: I did all of mine. 1999 Volvo V70 Abs Control Module Why?

A good DMM meter can check the capacitor reading. G. My e5 torx just came in the mail and some of you know where I was about to send this part. http://camtronics.net/speedometer-not/1998-bmw-528i-speedometer-not-working.html Begin by removing the needle.

The faster you short, the higher the speed. Some of them have numerous electrical issues, mainly involving the CEM, the wiring harness or other electrical problems. XC70, V70r, V70 AWD, S70 AWD. 9162675, 9140774 and 8602266. Care needs to be taken to see that the pin is rotated all the way clockwise to its stop before pushing the needle on at the stop point you found before

On a few units there might even be a metal wire seal (required in Sweden for taxi use). It feels like fuel starvation or something amiss with the air intake. It is connected with a connector and two wires. Speed is from ABS sensor for this model year.

Make note of where that position is. If either of the bare wires touch each other or the aluminum ABS pump block, this will trigger the ABS lights. Also, the wiring likes to fray where it enters the plug before the wheel sensor..almost always up front.